295/55R20 vs 285/60R20
285/60R20 is +0.69 in (+2.1%) in diameter and 0.39 in narrower than 295/55R20.
Size comparison295/55R20
| Dimension | 295/55R20 | 285/60R20 | Difference |
|---|---|---|---|
| Overall diameter UN R30 §6.1.2.1 | 32.78 in 832.5 mm | 33.46 in 850.0 mm | +0.68 in |
| Section width UN R30 §6.1.2.1 | 11.61 in 295.0 mm | 11.22 in 285.0 mm | −0.39 in |
| Sidewall height UN R30 §6.1.2.1 | 6.39 in 162.3 mm | 6.73 in 171.0 mm | +0.34 in |
| Rim diameter Marked on the tire | 20 in | 20 in | 0 in |
| Circumference From diameter | 102.97 in | 105.13 in | +2.16 in |
| Revolutions per mile From diameter | 615 | 603 | −12 |
| Allowed real diameter UN R30 §6.1.5 | 32.39–33.29 in | 33.06–34.00 in |
Nominal, not measuredReal tires vary by brand and load range.
- 295/55R20 32.78 in
- 285/60R20 33.46 in
Speedometer change
mph
If your speedometer is calibrated for 295/55R20 and you fit 285/60R20, the tire is +2.1% in diameter, so your true speed differs from the reading as shown below.
| Reading | True speed | Difference |
|---|---|---|
| 30 mph | 30.6 mph | +0.6 mph |
| 45 mph | 45.9 mph | +0.9 mph |
| 55 mph | 56.2 mph | +1.2 mph |
| 60 mph | 61.3 mph | +1.3 mph |
| 70 mph | 71.5 mph | +1.5 mph |
| 80 mph | 81.7 mph | +1.7 mph |
What changes
- Ride height changes by +0.34 in at the axle (half the diameter change).
- 285/60R20 is the taller tire.
- Revolutions per mile change by -12.
Nominal dimensions from the official sizing formula (sources below). This comparison doesn't check fit: wheel width, offset and clearance decide that. See changing tire size.
Each size
Printed from https://tiresizecalc.net/compare/295-55r20-vs-285-60r20/. Figures as published on 2026-11-01. The full working and the official sources are on that page.
Sources
- UN Regulation No. 30 - Uniform provisions concerning the approval of pneumatic tyres for motor vehicles and their trailers (Revision 3). United Nations Economic Commission for Europe (UNECE). E/ECE/324 E/ECE/TRANS/505 Rev.1/Add.29/Rev.3. 2007-03-29. Para 2.15 and 6.1.2.1: aspect ratio and outer diameter, D = d + 2H. Retrieved 2026-11-01.
- UN Regulation No. 54 - Uniform provisions concerning the approval of pneumatic tyres for commercial vehicles and their trailers (Revision 2). United Nations Economic Commission for Europe (UNECE). E/ECE/324 E/ECE/TRANS/505 Rev.1/Add.53/Rev.2. 2004-04-16. Para 6.1.2.1: the same formula for light truck tires. Retrieved 2026-11-01.
- UN Regulation No. 30 - Uniform provisions concerning the approval of pneumatic tyres for motor vehicles and their trailers (Revision 3). United Nations Economic Commission for Europe (UNECE). E/ECE/324 E/ECE/TRANS/505 Rev.1/Add.29/Rev.3. 2007-03-29. Para 6.1.5: allowed outer diameter, Dmin = d + 2H x 0.97, Dmax = d + 2H x 1.04. Retrieved 2026-11-01.
- Computed by tiresizecalc.net from the cited formula. Sri Murugan Systems. Circumference = pi x diameter; revolutions per mile = 63,360 / circumference; 1 in = 25.4 mm exactly. Retrieved 2026-11-01.
- Computed by tiresizecalc.net from the cited formula. Sri Murugan Systems. Speedometer: true speed = indicated speed x new diameter / old diameter. Retrieved 2026-11-01.
Last reviewed 2026-11-01. The full source list, with dates and file checksums, is in How the numbers are calculated. To report an error, email contactus@tiresizecalc.net.